Every now and again I end up helping a developer with a Wi-Fi issue. These fall into two groups: User-level Wi-Fi issues Development Wi-Fi issues A user-level Wi-Fi issue is one where the developer hasn’t created any of the products involved. An example of this is when you’re developing an app for an accessory and iOS is having problems connecting to that accessory but you don’t control the accessory’s firmware. In general, I recommend that you escalate such issues to the accessory vendor. They can then run their own investigation and, if necessary, file their own bug report. A development Wi-Fi issue is one that directly affects one of your products. For example, you’re developing a Wi-Fi accessory and iOS is having problems connecting to it. In that case, the onus is on you [1] to investigate why things are failing. If your conclusion is that iOS is behaving incorrectly, file a bug about that. IMPORTANT If you do file a bug in the context of some forums thread, please post your bug number to the thread, just for the record. When filing this sort of bug report it’s important to provide: Solid evidence that the problem is on the Apple side of the fence Enough information for Apple’s engineers to investigate it effectively Let’s start with that second point. If you can reproduce the problem reliably, install the Wi-Fi debug profile on your device, reproduce the problem, noting down a rough timestamp, and include the resulting logs and that timestamp in your bug report. Also, consider attaching a packet trace. There are three options here: Record a packet trace from the perspective of the Apple device. On iOS, use an RVI packet trace for this. Record a packet trace from the perspective of your accessory. Record a Wi-Fi level packet trace. You can do this from your Mac (see Recording a Wi-Fi Packet Trace) but it might be easier to do this with the infrastructure you used during the bring up of your accessory. It’s fine to include all three (-: Also include any relevant context about the issue. For example: If the issue is tied to a specific device model (In that case, it’d be good to include the above information for both the successful and failing cases.) If the problem shows up when joining from Settings > Wi-Fi, or whether it’s tied to a specific API, like NEHotspotConfigurationManager Finally, make sure to include an explanation of why you think this is an Apple bug, referencing specific items in the logs and packet traces that you attached. Of course, it’s only possible to do all of this if you can reproduce the problem. Investigating an intermittent issue based on reports coming in from users is much harder. It’s OK to file a bug about such issues, but your bug might not be actionable. At a minimum you should aim to include a sysdiagnose log with your bug. IMPORTANT This log has to be taken shortly after reproducing the problem. Don’t just attach any old log. One option is to request such a log from your users. I talk more about this in Using a Sysdiagnose Log to Debug a Hard-to-Reproduce Problem. You can also ask your users to file their own bugs using the Feedback Assistant app. It should automatically capture and attach a sysdiagnose log. Share and Enjoy — Quinn “The Eskimo!” @ Developer Technical Support @ Apple let myEmail = "eskimo" + "1" + "@" + "apple.com" [1] Well, your organisation. It’s rare to find a team where the same engineer works on both the iOS app and the accessory firmware. But if that’s you, good job!

Hi Team, I want to retrieve the list of nearby Wi-Fi networks (SSIDs) directly inside the app. Currently, I can see the available Wi-Fi networks by going to Settings → Wi-Fi on the device, but I would like to access that scan list programmatically within my application. I am developing the app using the Angular Ionic platform. On Android, I am able to get the nearby Wi-Fi scan list using the npm package @capgo/capacitor-wifi (v8.1.8). However, on iOS, the scan results are not being returned. If anyone has experience with this or knows how to achieve Wi-Fi scanning on iOS in Ionic/Capacitor, please let me know. Thanks.

Hi Team, I want to retrieve the list of nearby Wi-Fi networks (SSIDs) directly inside the app. Currently, I can see the available Wi-Fi networks by going to Settings → Wi-Fi on the device, but I would like to access that scan list programmatically within my application. I am developing the app using the Angular Ionic platform. On Android, I am able to get the nearby Wi-Fi scan list using the npm package @capgo/capacitor-wifi (v8.1.8). However, on iOS, the scan results are not being returned. If anyone has experience with this or knows how to achieve Wi-Fi scanning on iOS in Ionic/Capacitor, please let me know. Thanks.

Hi, I'v got the error by using NEHotspotConfiguration to connect a wifi spot but get:NEHotspotConfigurationErrorDomain code=8. I hope to get the same result as when scanning the code with the system camera. A pop-up window will appear, and I just need to click "Join" to successfully connect. Here's the logs: [OneAppWifi][iOS] handleCheckWifiEnabled start (iOS 12+) [OneAppWifi][iOS] handleCheckWifiEnabled pathUpdateHandler status=satisfied [OneAppWifi][iOS] handleConnectWifi start, ssid=OPPO Find X6 Pro, pwd=len=16, authType=Optional("sae"), hidden=false [OneAppWifi][iOS] handleConnectWifi cancelPendingConnection before new request ssid=OPPO Find X6 Pro [OneAppWifi][iOS] cancelPendingConnection called, errorCode=nil, currentSsid=nil [OneAppWifi][iOS] cancelPendingConnection silent cancel, just clear pendingConnectResult [OneAppWifi][iOS] handleConnectWifi apply completion with error, domain=NEHotspotConfigurationErrorDomain, code=8, userInfo=["NSLocalizedDescription": internal error.] [OneAppWifi][iOS] resolveNEError NEHotspotConfigurationErrorDomain code=8 [OneAppWifi][iOS] resolveNEError systemConfiguration / internal, map to connection_failed [OneAppWifi][iOS] handleConnectWifi resolved as failure errorCode=Optional("connection_failed") for ssid=OPPO Find X6 Pro [OneAppWifi][iOS] firePendingResult value=["success": false, "errorCode": Optional("connection_failed")], currentSsid=Optional("OPPO Find X6 Pro")

Hello, I submitted a Network Extension entitlement request (Packet Tunnel Provider) and opened case 102837721995. The case history says Apple sent a message on March 12, but I did not receive it and cannot reply through the support portal. Could someone from Apple Developer Support check the case? Also, it is possible that I misunderstood something or submitted the wrong entitlement request. My application will use WireGuard to establish the VPN connection. If a different entitlement is required for this scenario, please let me know. Thank you.

When using the official Wi-Fi Aware demo app on iOS, with the iOS device configured as a NAN Subscriber, after successfully establishing a peer-to-peer connection with another device via Wi-Fi Aware (NAN), the network path object nwPath.availableInterfaces does not list the nan0 virtual network interface. The nan0 interface is the dedicated NAN (Neighbor Aware Networking) interface used for Wi-Fi Aware data communication. Its absence from availableInterfaces prevents the app from correctly identifying/using the NAN data path, breaking expected Wi-Fi Aware data transmission logic. log: iOS works as subscriber: [onPathUpdate] newPath.availableInterfaces: ["en0"] iOS works as publisher: [onPathUpdate] newPath.availableInterfaces: ["nan0"]

com.apple.main-thread 0 StarMaker 0x5c40854 _isPlatformVersionAtLeast.cold.2 + 4425680980 1 StarMaker 0x526d278 -[FPRScreenTraceTracker displayLinkStep] + 191 (FPRScreenTraceTracker.m:191) 2 QuartzCore 0xbe924 CA::Display::DisplayLinkItem::dispatch(CA::SignPost::Interval<(CA::SignPost::CAEventCode)835322056>&) + 64 3 QuartzCore 0x9bf38 CA::Display::DisplayLink::dispatch_items(unsigned long long, unsigned long long, unsigned long long) + 880 4 QuartzCore 0xaf770 CA::Display::DisplayLink::dispatch_deferred_display_links(unsigned int) + 360 5 UIKitCore 0x7dee4 _UIUpdateSequenceRunNext + 128 6 UIKitCore 0x7d374 schedulerStepScheduledMainSectionContinue + 60 7 UpdateCycle 0x1560 UC::DriverCore::continueProcessing() + 84 8 CoreFoundation 0x164cc __CFMachPortPerform + 168 9 CoreFoundation 0x460b0 CFRUNLOOP_IS_CALLING_OUT_TO_A_SOURCE1_PERFORM_FUNCTION + 60 10 CoreFoundation 0x45fd8 __CFRunLoopDoSource1 + 508 11 CoreFoundation 0x1dc1c __CFRunLoopRun + 2168 12 CoreFoundation 0x1ca6c _CFRunLoopRunSpecificWithOptions + 532 13 GraphicsServices 0x1498 GSEventRunModal + 120 14 UIKitCore 0x9ddf8 -[UIApplication _run] + 792 15 UIKitCore 0x46e54 UIApplicationMain + 336 16 StarMaker 0x50c965c main + 18 (main.m:18) 17 ??? 0x19a9dae28 (缺少) Thread 0 libsystem_kernel.dylib 0x67f4 __semwait_signal + 8 1 libsystem_c.dylib 0xc7e4 nanosleep + 220 2 ZorroRtcEngineKit 0x1eb0f8 std::__Cr::this_thread::sleep_for(std::__Cr::chrono::duration<long long, std::__Cr::ratio<1l, 1000000000l>> const&) + 198 (pthread.h:198) 3 ZorroRtcEngineKit 0x27d30 zorro::KbLog::Loop() + 88 (kblog.cc:88) 4 ZorroRtcEngineKit 0x286e8 <deduplicated_symbol> + 4667967208 5 libsystem_pthread.dylib 0x444c _pthread_start + 136 6 libsystem_pthread.dylib 0x8cc thread_start + 8 Thread 0 libsystem_kernel.dylib 0x67f4 __semwait_signal + 8 1 libsystem_c.dylib 0xc7e4 nanosleep + 220 2 ZorroRtcEngineKit 0x1eb0f8 std::__Cr::this_thread::sleep_for(std::__Cr::chrono::duration<long long, std::__Cr::ratio<1l, 1000000000l>> const&) + 198 (pthread.h:198) 3 ZorroRtcEngineKit 0x19a4e4 zorro::ZkbLog::Loop() + 157 (zlog.cc:157) 4 ZorroRtcEngineKit 0x286e8 <deduplicated_symbol> + 4667967208 5 libsystem_pthread.dylib 0x444c _pthread_start + 136 6 libsystem_pthread.dylib 0x8cc thread_start + 8 Thread 0 libsystem_kernel.dylib 0x67f4 __semwait_signal + 8 1 libsystem_c.dylib 0xc7e4 nanosleep + 220 2 ZorroRtcEngineKit 0x1eb0f8 std::__Cr::this_thread::sleep_for(std::__Cr::chrono::duration<long long, std::__Cr::ratio<1l, 1000000000l>> const&) + 198 (pthread.h:198) 3 ZorroRtcEngineKit 0x19c4d8 zorro::QosManager::Loop() + 966 (string:966) 4 ZorroRtcEngineKit 0x286e8 <deduplicated_symbol> + 4667967208 5 libsystem_pthread.dylib 0x444c _pthread_start + 136 6 libsystem_pthread.dylib 0x8cc thread_start + 8

We are assisting a client with their app integration. The client believes that NEPacketTunnelProvider, NEHotspotHelper, and NEHotspotManager extensions stop functioning if the containing app hasn't been launched by the user within some recent window (e.g. 30, 60, or 90 days). We haven't been able to find any documentation supporting this claim. Specifically, we'd like to know: Is there any app launch recency requirement that would cause iOS to stop invoking a registered NEHotspotHelper or NEHotspotManager configuration? Is there any app launch recency requirement that would cause iOS to tear down or prevent activation of a NEPacketTunnelProvider? More generally, does iOS enforce any kind of "staleness" check on apps that provide Network Extension or Hotspot-related functionality, where not being foregrounded for some period causes the system to stop honoring their registrations? If such a mechanism exists, we'd appreciate any pointers to documentation or technical notes describing the behavior and timeframes involved. If it doesn't exist, confirmation would help us guide our client's debugging in the right direction. Thank you.

I am referencing: https://developer.apple.com/documentation/foundation/pausing-and-resuming-uploads Specifically: You can’t resume all uploads. The server must support the latest resumable upload protocol draft from the HTTP Working Group at the IETF. Also, uploads that use a background configuration handle resumption automatically, so manual resuming is only needed for non-background uploads. I have control over both the app and the server, and can't seem to get it to work automatically with a background url session. In other words, making multiple requests to get the offset then upload, easy but I am trying to leverage this background configuration resume OS magic. So anyone know what spec version does the server/client need to implement? The docs reference version 3, however the standard is now at like 11. Of course, I am trying out 3. Does anyone know how exactly this resume is implemented in iOS, and what exactly it takes care of? I assumed that I can just POST to a generic end point, say /files, then the OS receives a 104 Location, and saves that. If the upload is interrupted, when the OS resumes the upload, it has enough information to figure out how to resume from the exact offset, either by making a HEAD request to get the offset, or handle a 409. I am assuming it does this, as if it doesn't, the 'uploads that use a background configuration handle resumption automatically' is useless, if it just restarts from 0. Note, of course making individual POST/HEAD/PATCH requests manually works, but at that point I'm not really leveraging any OS auto-magic, and am just consuming an API that could really implement any spec. This won't work in the background, as the OS seems to disallow random HTTP requests when it wakes the app for URLSession background resumes. As of right now, I have it 'partially' working, insofar as the app does receive the 104 didReceiveInformationalResponse url delegate call, however it seems to then hang; it stops sending bytes, seemingly when the 104 is received. However, the request does not complete. In other words, it doesn't seem to receive a client timeout or otherwise indicate the request has finished. Right now, I am starting a single request, POSTing to a /files end point, i.e. I am not getting the location first, then PATCHing to that, as if I do that, the OS 'automatic' resuming fails with a 409, i.e. it doesn't seem to make a HEAD request and/or use the 409 offset correction then continue with the PATCH. Any idea what could be going on?

Hello and Good day! We are conducting Bonjour Conformance Test (BCT) for Printer device. BCT result is PASSED but with warning in Multicast DNS, specifically, WARNING: SHARED REPLY TIMING - UNIFORM RANDOM REPLY TIME DISTRIBUTION Other Shared Reply Timing is passed: PASSED: MULTIPLE QUESTIONS - SHARED REPLY TIMING - UNIFORM RANDOM REPLY TIME DISTRIBUTION Environment: BCT Tool Version: 1.5.4 (15400) MacOS Sequioa 15.5 DUT Firmware : Linux Debian 9 Apple mDNSResponder 1790.80.10 Service types: _ipps._tcp, _uscans._tcp, _ipp._tcp, _uscan._tcp Router : NEC AtermWR8370N Setup: 1-to-1 [Mac->Router<-DUT connection] Based on debug.log, this is where WARNING occurs: NOTICE 2026-03-04 10:51:06.870187+0900 _shared_reply_timing 04103: Shared reply response times: min = 26ms, max = 114ms, avg = 65.50ms WARNING 2026-03-04 10:51:06.870361+0900 _shared_reply_timing 04136: 50 percent of the replies within the correct range fell in the interval 20ms and 46ms (should be close to 25%). PASSED (SHARED REPLY TIMING) In the same debug.log for MULTIPLE QUESTIONS - SHARED REPLY TIMING is PASSED: NOTICE 2026-03-04 10:52:29.912334+0900 _shared_reply_timing 04103: Shared reply response times: min = 22ms, max = 112ms, avg = 78.00ms DEBUG_2 2026-03-04 10:52:29.912849+0900 recv_packet 01997: received packet (558 bytes) PASSED (MULTIPLE QUESTIONS - SHARED REPLY TIMING) [Details] Looking at Bonjour_Conformance_Guideline.pdf https://download.developer.apple.com/Documentation/Bonjour_Conformance_Test_Guideline/Bonjour_Conformance_Guideline.pdf there were some differences: In 1.6.2 Expected Result: Test Result File of Test that All Tests Passed, this is not displayed: PASSED: SHARED REPLY TIMING - UNIFORM RANDOM REPLY TIME DISTRIBUTION And in II.8 Shared Reply Timing: (Ideally, 25% of the answers should fall in each 21ms quadrant of the range 20ms - 125ms.) and comparing to the debug.log, there was a discrepancy of the interval, because 20ms and 46ms is 26ms interval. From RFC6762 6. Responding, Ideal range is from 20ms-120ms Because of this, please advise on the questions below: I would like to know on the possible cause and resolution for these WARNINGS. And since in current BCT result, (Test result integrity signature is generated), I would like to know if this is acceptable for BCT certification. Thank you.

We have a macOS system extension with NETransparentProxyProvider which is able to intercept traffic and handle it. We also wanted to setup few search domains from our network extension. However, unlike PacketTunnelProvider, NEDNSSettings are completely ignored with NETransparentProxyProvider. So whats the best way to setup few DNS search domains when using NETransparentProxyProvider.

Hey! We discovered an unexpected side-effect of enabling enforceRoutes in our iOS VPN application - video airplay from iOS to tvOS stopped working (Unable to Connect popup appears instead). Our flags combination is: includeAllNetworks = false enforceRoutes = true excludeLocalNetworks = true Interestingly, music content can be AirPlayed with the same conditions. Also, video AirPlay from iOS device to the macOS works flawlessly. Do you know if this is a known issue? Do you have any advice if we can fix this problem on our side, while keeping enforcRoutes flag enabled?

I am using Network framework for connecting two iPad devices that are connected through LAN and has Wifi enabled. I have enabled peerToPeerIncluded. I would like to understand how the framework chooses the interface types for browsing and discovering devices. When I start a browser with browser.run or listener.run, does the browser and advertiser browse and listen on all available interface types? My concern is that if it does in only one interface, Is there a chance that the browser is browsing in one interface(Lets say WiredEthernet) and the listener is listening on another interface(Lets say AWDL) and they dont discover?

We’re having an iPad issue accessing the local network with iPadOS 26.3. We have an automation system that tests our app on an iPad using accessibility tags. the XCTest test code sends messages from the iPad via TCP/IP to setup external test equipment. The messages abruptly stopped transmitting across the iPad blood-brain barrier with iPadOS 26.3 (26.2.1 and earlier works fine). The technique that worked involved installing a helper app with the same bundleID as our app, allowing the helper app to access the network, and when our app runs it has network access through the helper. It’s clever and kludgey. Forums that we referenced in the past: https://developer.apple.com/forums/thread/663858 TN3179: Understanding local network privacy | Apple Developer Documentation I suspect that something was changed in 26.3 that closed our window. I need two things: ID what is different in 26.3 and fix the automation system. If there’s a new way for XCUITest code to access the local network I’m happy to try it out.

I want to track down which part of an app contacts a given domain listed in its App Privacy Report. Following the instructions given here I am able to capture a packet trace, but traffic to the domain in question is encrypted using QUIC. Is there a way to insert e.g. mitmproxy into the capture process in order to get hold of the SSLKEYLOGFILE so that I can decrypt the traffic?

I'm using NEPacketTunnelProvider to intercept DNS queries, forward them upstream, and inject the responses back via writePacketObjects(). This works correctly for responses under ~500 bytes. For larger responses (~893 bytes, e.g. DNS CERT records), writePacketObjects() returns without error but mDNSResponder never receives the packet — it retries 3–4 times and then times out. What I have verified: IP and UDP checksums are correct UDP length and IP total length fields are correct Maximum packet size (MTU) set to 1500 in NEIPv4Settings/NEIPv6Settings Approaches tried: Injecting the full 921-byte packet — writePacketObjects() succeeds but the packet never reaches mDNSResponder IP-level fragmentation — fragments appear to be silently dropped Setting the TC (truncation) bit — mDNSResponder does not retry over TCP Truncating the response to ≤512 bytes — the packet arrives but the data is incomplete Questions: Is there a supported way to deliver a DNS response larger than 512 bytes through NEPacketTunnelFlow? Does NEPacketTunnelProvider impose an undocumented packet size limit below the configured MTU? Does mDNSResponder silently discard responses larger than 512 bytes when the original query had no EDNS0 OPT record? Is there a way to signal that larger responses are supported? Are IP-level fragments reliably delivered through writePacketObjects()? Tested on iOS 26.3, physical device.

We have a VPN app that uses NEPacketTunnelProvider with includeAllNetworks = true. We've encountered an issue where push notifications are not delivered over Wi-Fi while the tunnel is active in a pre-MFA quarantine state (tunnel is up but traffic is blocked on server side), regardless of whether excludeAPNS is set to true or false. Observed behavior Wi-Fi excludeAPNS = true - Notifications not delivered Wi-Fi excludeAPNS = false - Notifications not delivered Cellular excludeAPNS = true - Notifications delivered Cellular excludeAPNS = false - Notifications not delivered On cellular, the behavior matches our expectations: setting excludeAPNS = true allows APNS traffic to bypass the tunnel and notifications arrive; setting it to false routes APNS through the tunnel and notifications are blocked (as expected for a non-forwarding tunnel). On Wi-Fi, notifications fail to deliver in both cases. Our question Is this expected behavior when includeAllNetworks is enabled on Wi-Fi, or is this a known issue / bug with APNS delivery? Is there something else in the Wi-Fi networking path that includeAllNetworks affects beyond routing, which could prevent APNS from functioning even when the traffic is excluded from the tunnel? Sample Project Below is the minimal code that reproduces this issue. The project has two targets: a main app and a Network Extension. The tunnel provider captures all IPv4 and IPv6 traffic via default routes but does not forward packets — simulating a pre-MFA quarantine state. The main app configures the tunnel with includeAllNetworks = true and provides a UI toggle for excludeAPNS. PacketTunnelProvider.swift (Network Extension target): import NetworkExtension class PacketTunnelProvider: NEPacketTunnelProvider { override func startTunnel(options: [String : NSObject]?, completionHandler: @escaping (Error?) -> Void) { let settings = NEPacketTunnelNetworkSettings(tunnelRemoteAddress: "127.0.0.1") let ipv4 = NEIPv4Settings(addresses: ["198.51.100.1"], subnetMasks: ["255.255.255.0"]) ipv4.includedRoutes = [NEIPv4Route.default()] settings.ipv4Settings = ipv4 let ipv6 = NEIPv6Settings(addresses: ["fd00::1"], networkPrefixLengths: [64]) ipv6.includedRoutes = [NEIPv6Route.default()] settings.ipv6Settings = ipv6 let dns = NEDNSSettings(servers: ["198.51.100.1"]) settings.dnsSettings = dns settings.mtu = 1400 setTunnelNetworkSettings(settings) { error in if let error = error { completionHandler(error) return } self.readPackets() completionHandler(nil) } } private func readPackets() { packetFlow.readPackets { [weak self] packets, protocols in self?.readPackets() } } override func stopTunnel(with reason: NEProviderStopReason, completionHandler: @escaping () -> Void) { completionHandler() } override func handleAppMessage(_ messageData: Data, completionHandler: ((Data?) -> Void)?) { if let handler = completionHandler { handler(messageData) } } override func sleep(completionHandler: @escaping () -> Void) { completionHandler() } override func wake() { } } ContentView.swift (Main app target) — trimmed to essentials: import SwiftUI import NetworkExtension struct ContentView: View { @State private var excludeAPNs = false @State private var manager: NETunnelProviderManager? var body: some View { VStack { Toggle("Exclude APNs", isOn: $excludeAPNs) .onChange(of: excludeAPNs) { Task { await saveAndReload() } } Button("Connect") { Task { await toggleVPN() } } } .padding() .task { await loadManager() } } private func loadManager() async { let managers = try? await NETunnelProviderManager.loadAllFromPreferences() if let existing = managers?.first { manager = existing } else { let m = NETunnelProviderManager() let proto = NETunnelProviderProtocol() proto.providerBundleIdentifier = "<your-extension-bundle-id>" proto.serverAddress = "127.0.0.1" proto.includeAllNetworks = true proto.excludeAPNs = excludeAPNs m.protocolConfiguration = proto m.localizedDescription = "TestVPN" m.isEnabled = true try? await m.saveToPreferences() try? await m.loadFromPreferences() manager = m } if let proto = manager?.protocolConfiguration as? NETunnelProviderProtocol { excludeAPNs = proto.excludeAPNs } } private func saveAndReload() async { guard let manager else { return } if let proto = manager.protocolConfiguration as? NETunnelProviderProtocol { proto.includeAllNetworks = true proto.excludeAPNs = excludeAPNs } manager.isEnabled = true try? await manager.saveToPreferences() try? await manager.loadFromPreferences() } private func toggleVPN() async { guard let manager else { return } if manager.connection.status == .connected { manager.connection.stopVPNTunnel() } else { await saveAndReload() try? manager.connection.startVPNTunnel() } } } Steps to reproduce Build and run the sample project with above code on a physical iOS device. Connect to a Wi-Fi network. Set excludeAPNS = true using the toggle and tap Connect. Send a push notification to the device to a test app with remote notification capability (e.g., via a test push service or the push notification console). Observe that the notification is not delivered. Disconnect. Switch to cellular. Reconnect with the same settings. Send the same push notification — observe that it is delivered. Environment iOS 26.2 Xcode 26.2 Physical device (iPhone 15 Pro)

Is it somehow possible to get the transport layer (UDP and TCP) payload amounts for TLS or QUIC connections established via the Network framework? (From within the app itself that establishes the connections.) I am currently using the ntstat.h kernel socket calls, but I hope there is a simpler solution. With ntstat, I have not yet been able to observe a specific connection. I have to search for the connection I am looking in all (userspace) connections.

Since updating to macOS 26.4 developerbeta 2 I've been getting full loss of dns resolution. I am not running a VPN or any network extensions that I am aware of. I'm not sure how to report this in the feedback utility as I cannot find an appropriate category for it. Happy to file it if someone can give an appropriate suggestion - the closest I could see was Wi-Fi but that wanted Wi-Fi logs for the issue, which I do not believe to be needed as this is not a Wi-Fi connectivity issue. Running dig example.com +short nslookup example.com ping example.com Gives the following output 104.18.27.120 104.18.26.120 Server: 10.0.1.1 Address: 10.0.1.1#53 \ Non-authoritative answer: Name: example.com Address: 104.18.26.120 Name: example.com Address: 104.18.27.120 \ ping: cannot resolve example.com: Unknown host This shows it's not an issue with my local network and that core networking is working, but something in the mDNSResponder/dns stack of macOS is failing. This causes all apps/browsers that do not implement their own DNS lookups to fail (Chrome still works). Sometimes the issue clears after running the following commands (for a period), sometimes it does not. A restart always resolves the issue temporarily. sudo killall -9 mDNSResponder sudo killall -9 mDNSResponderHelper sudo dscacheutil -flushcache sudo ifconfig en0 down sudo ifconfig en0 up

I’m encountering a persistent issue with my Network Extension (specifically NEFilterDataProvider) and would really appreciate any insights. The extension generally works as expected, but after some time — especially after sleep/wake cycles or network changes — a global network outage occurs. During this state, no network traffic works: pings fail, browsers can’t load pages, etc. As soon as I stop the extension (by disabling it in System Preferences), the network immediately recovers. If I re-enable it, the outage returns instantly. I’ve also noticed that once this happens, the extension stops receiving callbacks like handleNewFlow(), and reinstalling the app or restarting the extension doesn’t help. The only thing that resolves the issue is rebooting the system. After reboot, the extension works fine again — until the problem reoccurs later. I asked AI about this behavior, and it suggested the possibility that the kernel might have marked the extension as untrusted, causing the system to intentionally block all network traffic as a safety mechanism. Has anyone experienced similar behavior with NEFilterDataProvider? Could there be a way to detect or prevent this state without rebooting? Is there any logging or diagnostic data I should collect when it happens again? Any guidance or pointers would be greatly appreciated. Thanks in advance!